ead>

apradravya wand

At A Glance Author anonymous Contact anonymous@bme.anon Artist self Action Plan! Prince's wand retained by a "T" bar apadravya. It was not my intention to repeat the story I wrote to gain access to BME Extreme back in 1997. Then I told you about how I sharpened a 6mm stainless steel tube by putting it in an electric drill chuck and grinding it sharp; thereafter putting it into my meatus and pointing it at a wooden board and hitting it with a hammer - effectively cutting a 6mm PA hole out of the bottom of my glans. At that stage I had never heard of a "Prince Albert", nor was it my intention to wear a ring in the end of my prick. My plan was to relocate the outlet for urine and ejaculation and this I did by permanently sealing off the original hole. I dipped a cotton bud in hydrochloric acid and destroyed the skin surrounding the original internal urethral opening - rubbing it until it bled. By inserting sugar mixed with Bettadine and keeping the hole shut with Elastoplast the opening I was born with healed shut. Still without knowing about BME I started injecting my testicles with various substances including oestrogen. Whether it was a testicular rejection or a failure of hygiene I don't know but my left ball flared up and had to be removed. This was done by a urologist under general anaesthetic. I pleaded for the swollen orb to be removed through the scrotum but was told that the sac did not heal readily and that the cords had to be inspected in case of malignant growths. Needless to say, I did not own up to the activities that led to the condition. I also requested that my scrotum be removed entirely (or partially) which the surgeon flatly refused to do. Since the operation I have tried to kill off the remaining testicle by cutting off the blood supply with elastic bands and deadening the pain by freezing. I have further tried to achieve gelded status by means of a home made burdizzo. The first one was a "G" clamp with two oval nails fixed in position, edge on, to make the cutting surfaces. The second was similar but using vice grips. In both the latter attempts I first sewed the vas deference to the wall of the sac to stop it from running away. But, I still have my right ball! Maybe I will try opening the scrotum along the rafe one-day and cut the remaining ball out ...... My current project is to be able to wear a wand, PERMANENTLY! The bigger the better! One of your correspondents stated that he couldn't wear one permanently because "it is just too damn distracting!" That is exactly what I hope to achieve! In the absence of sounds I have used knitting needles to stretch the urine duct, starting with 7mm and progressing to 10mm. The sharp points were first filed down to rounded ends to prevent damage to the walls of the urethra. Now I can now accommodate a 10mm urethral tube. The curve of the urethra wont allow my penis to hang down my trouser leg a with a tube of more than 125mm in length inserted: when erect a rod of 150mm in my piss hole is quite comfortable. Accordingly I have manufactured a 10mm diameter 125mm long Princes Wand with 2mm-threaded hole for the retaining stud. The retaining stud is to be a "T" bar situated behind the coronal ridge of the glans. The discharge hole in the urethral tube is only 3mm in order to keep the wand as heavy as possible. In its unembelished state the wand weighs 100g. I plan to create the heaviest drain plug possible; perhaps 30 or 40 mm in diameter, which should stretch Mr Penis - SERIOUSLY! However there are two problems: i) There is no way my wife will countenance that (or ANY genital jewellery - my foreskin hides those mods already made). ii) Because my sub-incision is now my "normal" urethral opening, the mechanism to hold the wand in place will have to be a bar vertically through the penis, but behind the glans so as to be hidden by my foreskin Somewhere in BME I read that the piercing for the retaining stud of a wand had to be completely healed before being used to keep a wand in place. I have had a 2mm thick gold "T" bar with a screw thread manufactured by a jeweller. I have also made a short 8mm tube, drilled and tapped to accommodate the "T" bar during the healing process. I have purchased a 2.6mm piercing tool and, after sterilising and anaesthetising, pushed it through my penis - intending to push the "T" bar through the newly made hole and then place the 8mm tube in my urethra and screw the "T" bar into that, leaving it in place until everything is nicely healed...Only the 2mm bar wouldn't go through the 2.6mm hole. - HELP! Return to Apadravya experiences